PROTOTYPE Weekend Proto Fun 1/27/2023

BNSF FAN Jan 27, 2023

  1. BNSF FAN

    BNSF FAN TrainBoard Supporter

    9,892
    29,169
    148
    Happy weekend all! Lets kick off the Weekend Proto Fun with a couple of switchers. Last Friday evening I was passing through Longview TX and jumped off I-20 to check out a small locomotive rebuilder there. These two fellows were among the sights to see. Not sure what's up with the cab on the black and grey unit but sure looks interesting, maybe one of those IC Paducah rebuilds? Enjoy the weekend!
    527.JPG 515.JPG
     
  2. r_i_straw

    r_i_straw Mostly N Scale Staff Member

    22,210
    49,630
    253
    Switching the yard in Hearne, Texas, in February 1996.
    27401.jpg
     
  3. Hardcoaler

    Hardcoaler TrainBoard Member

    10,676
    44,850
    142
    From a cold and wet 10/21/1996 at Scholle, NM. The crew invited my wife and I into the cab of the 943 to warm up while we waited for an opposing train to appear. Scholle siding is east of Abo Canyon. Abo Canyon was a single track bottleneck at the time, so Scholle saw a lot of action as trains stacked up there. After years of battles to gain environmental permits, BNSF completed double tracking Abo in 2011.

    1996-10-21 006 Scholle NM - for upload.jpg

    1996-10-21 004 Scholle NM - for upload.jpg
     
  4. gmorider

    gmorider TrainBoard Member

    2,093
    6,282
    65
    @BNSF FAN, black and grey cab redesigned with the claustrophobe in mind.
     
  5. BoxcabE50

    BoxcabE50 HOn30 & N Scales Staff Member TrainBoard Supporter

    67,560
    22,734
    653
    I might have previously shared this one. This is Rayonier's #23 shop switcher, which was once used at their well noted Railroad Camp engine facilities, in Washington State. [​IMG]
     
    fordy744, gjslsffan, RailMix and 10 others like this.
  6. HemiAdda2d

    HemiAdda2d Staff Member TrainBoard Supporter

    22,014
    27,407
    253
    A 2x3x1 BNSF combo (double) grain train is underway on main track #1 leaving Minot:
    _MG_2750.jpg
     
  7. badlandnp

    badlandnp TrainBoard Member

    4,587
    16,153
    90
    From clean back in July of 2017, some BN throwback at Glendive,

    PIC_0293.JPG
     
  8. Mike VE2TRV

    Mike VE2TRV TrainBoard Member

    4,867
    12,443
    92
    Looks like an SW1001, an SW1000 with a low-clearance cab, that got a Paducah-like roof job.

    "Low clearance cab" means it can get into tighter spaces, but you have to duck to get in it if you're 5'9" or taller... :D
     
  9. gjslsffan

    gjslsffan Staff Member

    2,626
    5,747
    69
    Here we have my great friend A C (Woody) Woodward on his usual WB train out of DV to GJ, working the inter-divisional pool in 1998. We see him here, on the super elevated curve, just east of the east switch Palisade CO 1998, almost home. You can see why I model the under-frame and other details.
    Note the welded over Mars light housing, and class lights, horn re-location, also note the almost white color of the trucks and under frame. This is due to many hours of the sanders being on, also note the PTC (not positive train control) cables, the bell, fuel filler necks and many other details.
    Note, the Black paint under the dyn brake grids fading. I think the discoloring is maybe from the heat from the engine's exhaust and not just dynamic brake heat build up. The exhaust manifolds on these EMD's would glow red hot upon hours of run 8 in the long grades, look at the fading increases towards the turbo/exhaust. The dyn brakes would also make great deal of heat for the grids, but I dont see any heat discolorations on this units upper Dyn grid environs. I also note a couple journal boxes have a wet/dark on the bottom appearance as well. This is due to the shop forces doing their job. There was no rubber type seal between the journal boxes and axle, it's a machined/close type fit, and nobody wanted to be they guy that didn't put enough oil in the journal boxes. Also the ratchet type hand brake has been replaced too. Many great details to see here.
    Dang near Miller time.
    Woody at east Palisade.jpg
     
  10. Daves_Trains

    Daves_Trains TrainBoard Member

    136
    1,811
    23
    A few projects from 2005 at the OERM.

    pic 015.jpg
     
    fordy744, SP-Wolf, Kurt Moose and 9 others like this.
  11. HemiAdda2d

    HemiAdda2d Staff Member TrainBoard Supporter

    22,014
    27,407
    253
    Tom,
    Thanks for the great rundown on the details. I'd like to know more about the PTC (Positive traction control modified--borrowed from the SD50s--increased tonnage rating to that of the SD50). Are they similar to the speed recorder cables we see on the rest of SD40-2 production?
     
    BNSF FAN, gjslsffan and Mike VE2TRV like this.
  12. dualgauge

    dualgauge TrainBoard Member

    411
    448
    24
    The black & gray switcher was working at a steel mill.Looks like was AK Steel by the faded lettering.
     
    BNSF FAN, gjslsffan and Mike VE2TRV like this.
  13. badlandnp

    badlandnp TrainBoard Member

    4,587
    16,153
    90
    "Are they similar to the speed recorder cables we see on the rest of SD40-2 production?"

    Yes, for the short answer. Several aftermarket outfits marketed different versions, Q-Tronics and a couple others that promised better controlled wheelslip. Theoretically a very slight amount of slip does provide better traction, so with a speed generator on each axle that sends signals to the 'puter, which compares speeds and is able to adjust power to the motors appropriately, allowing a tiny bit of slip. It does work out better.
     
  14. Mike VE2TRV

    Mike VE2TRV TrainBoard Member

    4,867
    12,443
    92
    PTC - Positive Traction Control, not the more recent Positive Train Control - was developed by CN's R&D department in the late 60s and early 70s to solve the problem of their very "slippery" GP40s. They had a tendency to spin their wheels like a souped-up hot rod doing donuts in a parking lot.

    Some tests of the completed prototypes were using fuel oil injected on the tracks ahead of the wheels to provoke wheel slip. A 45-gallon drum of the stuff was perched on the right front walkway just in front of the engineer's position of GP40 4006. To CN 4013 went the honor of becoming the first diesel-electric locomotive with a wheelslip control system using individual axle torque control. They managed to get a 20% gain in tractive effort.

    It was definitively implemented on CN's 40-2 series locomotives, the GP40-2W and SD40-2W.

    That all got the ball rolling for future wheelslip control development by both EMD and GE. CN showed them the way!
     
  15. badlandnp

    badlandnp TrainBoard Member

    4,587
    16,153
    90
    That's a neat bit I didn't know, from back when railroads had their own research folk! Thanks!
     
  16. PGE-N°2

    PGE-N°2 TrainBoard Member

    911
    1,272
    33

Share This Page